Help support TMP


"WWII German horse drawn ambulance wagon now available" Topic


12 Posts

All members in good standing are free to post here. Opinions expressed here are solely those of the posters, and have not been cleared with nor are they endorsed by The Miniatures Page.

Remember that you can Stifle members so that you don't have to read their posts.

For more information, see the TMP FAQ.


Back to the Wargaming in Australia Message Board

Back to the 20mm WWII Message Board

Back to the 3DPrinting Message Board

Back to the Blogs of War Message Board

Back to the 28mm WWII Message Board

Back to the WWII Land Gallery Message Board


Areas of Interest

General
World War Two on the Land

Featured Hobby News Article


Featured Link


Featured Showcase Article

Red Sable Brushes from Miniaturelovers

Hobby brushes direct from Sri Lanka.


Featured Workbench Article

Useful Wooden Products at Dollar Tree

Scratch-builders often need basic wood shapes. Here is what is available inexpensively at the dollar store.


Featured Profile Article

My Wargaming Blood Revealed

Personal logo Editor in Chief Bill The Editor of TMP Fezian gets his DNA results, and starts thinking about wargaming.


Featured Book Review


903 hits since 27 May 2023
©1994-2024 Bill Armintrout
Comments or corrections?

Gunner Dunbar27 May 2023 8:59 p.m. PST

Hi guys

All constructive criticism welcome
Here's the first test print, a couple of areas needed fixing the shovel and an axle seems a little weak, have fixed those areas, file is now available at link ,use the free horses located on My shop I'm also working on some medic drivers which will also be made available for free. For physical prints email me at Dan.dunbar@hotmail.com
link

picture

picture

picture

picture

picture

picture

14Bore28 May 2023 3:54 a.m. PST

Amazing what you are doing

Gunner Dunbar28 May 2023 5:39 a.m. PST

Maybe, it's all coming to a screaming halt though, I've had 3 people come forward saying the files are causing an error in their software, they work at my end, if I can't figure it out I may change to supplying prints only rather than files.

jgawne28 May 2023 6:19 a.m. PST

I had this issue with some other files (someone else's). They had worked for lots of people, but when I tried to slice they gave me error messages on them that they needed to be repaired. Some could be repaired, some could not. Some would not work in Lychee, but would work in Chitubox.

IN playing around with them, I suspect (but can not prove) that it had something to do with how much memory was available on my computer. Can't prove it, but it seemed if I had too much stuff open, it would sometimes give me errors. Gave up on Lychee and just ended up using CHitubox.

Please do not stop making your stuff available because a few people have issues. I have not tried any of them, but if you say what files are problematic, I'll see how they slice for me.

David Manley28 May 2023 9:52 a.m. PST

Please don't stop posting your models, if there are errors then opening the file in MS 3D Builder usually fixes it. I've had similar issues with models I've bought.

jgawne28 May 2023 12:32 p.m. PST

For what it is worth, I had downloaded the first German wagon and horses the other day- I tried to open them in Chitubox, and was unable to. The 'item' just would not appear on the Chitubox plate. Sorry I don't know enough to be of further help.

Gunner Dunbar28 May 2023 1:19 p.m. PST

OK, that another one with issues, I'm pulling them, sorry guys.

Gunner Dunbar29 May 2023 6:44 a.m. PST

I have run these files through netlabb mesh fixer in fusion 360, please re download and try again

Serge6929 May 2023 7:31 a.m. PST

Great!!!!!!!!

Hornswoggler29 May 2023 11:28 p.m. PST

… I may change to supplying prints only rather than files.

A while ago when I asked about buying some prints, here:
TMP link

The response was that you wouldn't sell bare prints. Did that only apply to prints from files that aren't your own IP?

Gunner Dunbar30 May 2023 4:17 a.m. PST

Hi Hornswoggler

Yes, IP issues,, I'm happy to sell prints of my own files.

Hornswoggler30 May 2023 11:46 p.m. PST

Thanks for clarifying that.

Sorry - only verified members can post on the forums.