Winston Smith | 27 Jun 2016 3:14 a.m. PST |
That sounds like a very dumb idea. |
Gunfreak | 27 Jun 2016 3:36 a.m. PST |
Sounds like a lot of work. |
Cerdic | 27 Jun 2016 3:37 a.m. PST |
Sounds like a way to sell a lot more paint…. |
TKindred | 27 Jun 2016 3:52 a.m. PST |
I've done this, and it works quite well. Having said that, a better solution is to simply lay them flat on a large piece of foam core and spray one side, let it dry, then spray the other. That's how I've been priming for several years now. For shields, I put down a strip of double-sided tape and stick the shield to it so the back is up. Spray that, then when dry flip them over and spray the face. I also paint pikes, spears and javelins, etc, before attaching them. These I take a piece of balsa wood or foam core, and push the point of the pike into it so the pike blade is fully concealed. Then I spray the shafts with whatever color I'm wanting them to be. |
Who asked this joker | 27 Jun 2016 5:53 a.m. PST |
You could do that or you could just use a drop of glue on each base and put them on a strip. Why waste the primer? |
etotheipi | 27 Jun 2016 6:24 a.m. PST |
I would think the drying time for the primer would be a limiting factor. I usually base, then paint, anyway. |
John the Greater | 27 Jun 2016 7:02 a.m. PST |
I'm with joker. I cut up old business cards (in my line of work I have hundreds of them available) and put on a drop of glue to fasten the figures. No paint wasted. |
dandiggler | 27 Jun 2016 7:09 a.m. PST |
I never thought of this, I usually use a small dab of white glue to mount them to popsicle sticks. |
WillieB | 27 Jun 2016 7:26 a.m. PST |
I use a magnetic strip on a piece of hardwood. All my figures are on metal bases. When the paint gets too thick simply scrape it off and re- use. |
Col Durnford | 27 Jun 2016 7:47 a.m. PST |
For my 20mm figure I use white glue and a 1 inch high by 1/2 inch wide wooden stick both for priming and final painting. After the figures are complete, I remove them from the rods. Finally I use a dermal sand down both the bases of the figures and the wooden rods for the next batch. |
Martian Root Canal | 27 Jun 2016 8:03 a.m. PST |
Sounds like a good way to get an uneven or blotchy primer job on the side that is laying in the wet primer. |
Scorpio | 27 Jun 2016 9:33 a.m. PST |
|
Pictors Studio | 27 Jun 2016 10:40 a.m. PST |
I just dip them in my hot glue pot and stick them on the stick. No hassles, dries instantly, fast and you can get painting right away. |
rabbit | 27 Jun 2016 11:41 a.m. PST |
Double sided tape them to a stick, waaay cheaper than paint If you are careful you can reuse the tape as the figures, once removed, leave a sticky void. Just not as sticky as before. |
Doctor X | 27 Jun 2016 11:59 a.m. PST |
Great idea to sell more overpriced primer. I give them credit for that. Scrap wood with magnetic tape on it, all my bases are metal so they stick to the magnet with no problem. I can put about 20 28mm figs on them and get a good angle to prime even those tough to reach spots. When dry they just lift off. I've been using the same strips for a few years now with no issues. |
legatushedlius | 27 Jun 2016 12:51 p.m. PST |
For plastics I undercoat them on the sprue – stops small bits like shields being blown away. Just rest the sprue on a cork to lift it above the surface. Flip over and spray the other side. You only have to touch up a few small contact points after you cut the pieces off. No gluing/sticking required. |
COL Scott ret | 27 Jun 2016 7:27 p.m. PST |
I mostly do plastics and I do them the same way as Legatus. |
Hafen von Schlockenberg | 28 Jun 2016 8:15 a.m. PST |
I've been using TKindred's method for decades now (gulp!). After priming, I stick them on popsicle sticks for painting(tongue depressors for 25mm) with a hot glue gun. I tried putting them on sticks first a couple of times,but I found he sticks can obscure the undercuts on the lower parts of the figures. Perhaps I "overprime". . . I do plastics same as Legatus and COL Scott,though. |
Frederick | 28 Jun 2016 9:31 a.m. PST |
I prime the figures standing up glued to bases with white glue but do it outdoors and spray from all four sides – needless to say I do this with figs en masse and given the weather it does require planning ahead |