Help support TMP


"Basing for Lasalle and other questions?" Topic


7 Posts

All members in good standing are free to post here. Opinions expressed here are solely those of the posters, and have not been cleared with nor are they endorsed by The Miniatures Page.

Please do not use bad language on the forums.

For more information, see the TMP FAQ.


Back to the Napoleonic Discussion Message Board


Areas of Interest

Napoleonic

Featured Hobby News Article


Featured Link


Featured Showcase Article

1:600 Xebec

An unusual addition for your Age of Sail fleets.


Featured Workbench Article

Building Two 1/1200 Scale Vessels

Personal logo Virtualscratchbuilder Supporting Member of TMP Fezian builds a cutter and a corsair, both in 1/1200 scale.


Featured Profile Article


Current Poll


Featured Book Review


1,036 hits since 20 Nov 2009
©1994-2026 Bill Armintrout
Comments or corrections?

ThomasS20 Nov 2009 11:06 p.m. PST

First off new to Napoleonic and 15mm, so hope my questions are not to stupid. I've got my order in for Lasalle and decided on 15mm Battle Honor for figures and bases(that order goes in next paycheck).

The recommended basing for infantry and cavalry is 1.5"x1" and artillery and limbers the same width of 1.5". I've already decided to use the recommended for cavalry and 1.5"x0.5" for the infantry(to save on model count for cost and painting time). I can always just double up the infantry stands later to get the recommended size if need be.

So my questions are these.
1. Will 1.5"x1" be deep enough for artillery from Battle Honor?
2. How deep of base will I need to fit limbers on from Battle Honor?
3. What other Napoleonic rule sets use the same basing? infantry 1.5"x.5"/cavalry 1.5"x1"?

Thanks

Onomarchos21 Nov 2009 4:05 a.m. PST

Shifter,

I use AB for my arty on 1.5" deep stands. They are a little tight, but OK. I think BH should be the same.

On the limber question, I use AB four horse limbers. How many horses on the BH? Also do you want the gun to hang off the limber base when limbered or do you want to have a space for it? These factors determine what you will need for limber stand depth.

Mark

Maxshadow21 Nov 2009 6:11 a.m. PST

Hi I've got some Battle Honors Guns (along with AB and Essex ones as well) and they all fit on a 1.5 inch stand OK.
I use 2 horse limbers on 1.5 inch front by 2 inch long stands. If you want to use 4 horses then add another inch in length.
Good luck and hope you enjoy the Napoleonic period.
regards
Max

ThomasS21 Nov 2009 7:32 a.m. PST

Thanks for the answers.

foot soldier21 Nov 2009 8:37 a.m. PST

Shifter,
There are AB Lasalle unit packs available from Eureka Miniatures USA & Eureka Miniatures Australia. In accord with Honour Publishing, we are offering a range of Unit Packs made up of AB figures & Eureka Miniatures specifically tailored for use with these rules.

cheers,
rob
eureka miniatures usa

ThomasS21 Nov 2009 9:17 a.m. PST

@foot soldier
Well, I have been looking at the artillery/limber and cavalry unit packs you have. At this time going to pass on the infantry unit pack, since I'm basing 16 to a unit not 32. Once Sam gets part 2 of the Honor series done Blucher(each stand a battalion) I'll be all over AB for infantry command groups.

foot soldier21 Nov 2009 10:07 a.m. PST

Shifter,
As the AB figures are sold individually you can always just make up your own units of 16. The units of 32 were Sam's recommendation.


cheers,
rob
eureka miniatures usa

Sorry - only verified members can post on the forums.